Configuration of High speed internet access

Procedure for Configuration of High-Speed Internet Access

using CDMA EV-DO Data Card (ZTE Make).

1. Install the ZTEPSTv1.03.04 Software on PC for configuration of CDMA EV-DO Data Card (ZTE Make).This can be used as CDMA 2000 1x as well as 1x EVDO both.

2. Insert the CDMA EV-DO Data Card (ZTE Make) which is to be configured in USB Slot

of the PC & Also insert the CD provided with Data Card. Run the Setup.exe file from CD

so that the ZTE EV-DO Data card USB Setup is installed & an icon titled “ZTE EV-DO”

will appear on desktop.

3. Also install QPST Software for RL editor. Reset the PC after Installation . Run RL editor from programs in start menu and select IS-683A+1xEV and then check Preffered Only, default roaming Indicator 0 Preferred Roaming List ID 0. Then edit Acquisition Record Table & System record table as-

Acquisition Record Table:

Index	Acq Type	Band Class1	CH#1
0	CDMA(channels)	0-800 MHz Cellular	42
1	HDR(channels)	0-800 MHz Cellular	83

System record table:

Index	System Type	Neg/Pref	Geography	Priority	Acq Index	SID	NID
0	IS-2000 System	Preferred	New	Same	0	14496	65535
1	IS-856 System	Preferred	Same	Same	1

Subnet ID	Roam Indicator	Assn. Incl.	Assn. Tag	PN Assn	Data Assn.
	0	Yes	0	Yes	Yes
/0	0	Yes	0	No	No

Now save this file , and in ZTEPST software locate the PRL file and then select for card programming as below given.

Note: For 1x only Index 0 i.e. CDMA ony & IS-2000 System should be written for EVDO both.

4. Double click on this icon – a Configuration window titled “ZTE _PST V1.03.04” will

appear on screen .

Select appropriate COM Port (USB slot) where the CDMA EV-DO Data Card is inserted

& ensure that COM port shows the status as “Connected”(Highlighted in Green colour) &

“DB Success” tab at the bottom is highlighted in Green colour.

When COM port status is displayed as “Connected”, click on the “Read from Phone” tab

at the bottom left of the window enter Service Programming Code 000000 and click OK.

1. In General Tab Slot cycle 2

and Lock code 0000

2. In CDMA Tab

Ident

NAM 2030707

Directory 3612030707

AOC 0

Akey Info

Akey: keep blank

Check Input

CDMA

Phone Number:

MC 404 11_12 00

IMSI_S 3612030707

Channel:

Keep Blank

EVRC Service Options:

Check EVRC Enabled and select 13K for Home, Home Orig and Roam Orig.

System

Home SID/NID:

No. NID SID

0 65535 14496

1 65535 14496

Set Pref Mode, Band Pref, Roam Pref & System Pref as

‘Automatic’ & Hybrid Pref as ‘Off’.

Roam

Chek PRL Enabled and browse for PRL backup as edit from RL editor above.

M.IP

Select MIP/SIP Mode: Simple Only

Re- reg Threshold: 0

ActiveProf Index: 0

And rest keep Blank.

PPP

PPP Um:

User ID: 165

User Password:165

PPP An:

AN_AUTH: 190

AN_AUTH_Passwor: 190

PPN An only for EVDO not for 1x.

5. Click on the “Write to Phone” tab at the bottom left of the window.The software will

probe about updating the database record ,click ‘Yes’.The configuration of Data Card

using the ZTEPSTv1.03.04 Software is complete.

11. Now Double-click on the “ZTE EV-DO” icon on desktop – an interface window will

appear on screen. Select Setting - Network tab & Enter the following information –

Phone - #777. Username & Password as provided.

Click on the ‘Apply’ tab to effect the changes. The configuration is complete. Click on

the “Connect/Disconnect” tab on upper left hand side so as to be able to use the High-

speed internet service using CDMA EV-DO Data card.(Kindly reset the PC if needed

after completion of configuration.)

**********************************************************************